Products:
Pneumatic
| Jump to: Pneumatic Transducers |
 | Electronic to Pneumatic Transducer  ETP-9500: This unit installs between the controller and a pneumatic device. It offers a low cost alternative for retrofit or new construction installations. It is available in 4-20ma and 0-10vdc 2wire or 3 wire versions, with or without an enclosure. |
 | Enclosure ENC1: Protects transducers or any automation or HVAC component. Twenty gauge metal, 2" diameter opening in cover for guage, two 7/8" diameter openings in the base ends for 1/2" EMT fitting for wiring connection, plastic snap-in covers for all openings.Size: 3.05" W x 3.3" H x 6" L. |
 | Floating Point to Pneumatic Output
EFP*: Input: Two Digital (relay, triac, or transistor) 9-24 VAC/VDC. Output: Jumper selectable 0 - 10, 0 - 15, or 0 - 20 psig air pressure. Rate of Change: 30, 45, 60, 90 sec., 2, 3, 6, and 8 minutes. Manual Override. Power: 24 VDC or 24 VAC @ 4A. Size: 4.0" L x 3.45" W x 1.875" H. Anodized aluminum manifold. |
 | Analog to Pneumatic Output
EPC*: Input: 0-5, 0-10 or 0-15 VDC/Infinite ohm, or 4-20 mA/250ohm. Output: 0-20 psig. Feedback: 0-5 VDC= selected output. Power: 24 VAC or VDC (50/60 HZ) @ 160 mA. Valve exhaust (EPC2), bleed-type in 41 scim (EPC), & dual Fail-safe (EPC3FS). Aluminum manifold. Gauge Optional |
 | Analog to Pneumatic Output EPCB: Input: 0-5, 0-10 or 0-15 VDC/Infinite ohm, or 4-20 mA/250ohm. Output: 0-10, 0-15 and 0-20 psig. Feedback: 0-5 VDC= selected output. Power: 24 VAC or VDC (50/60 HZ) @ 180 mA. Controlled exhaust dual valve. Fail-safe model EPC2GFSB. Aluminum manifold. Rugged painted metal housing. |
 | Pulse Width Modulated to Pneumatic Output
EPW*: Input: 0.1 - 10, 0.02-5, 0.023-6 or 0-10 sec. Duty cycle, 0.59 - 2.93, 0.1 - 25.5 sec. or 0 - 20 V phase cut. Trigger: 9 - 24 VAC/VDC. Output: 0 - 10, 0 - 15, 0 - 20 psig Manual override. Feedback: 0 - 5 VDC = range. Power: 24 VDC or 24 VAC @ 160mA. Valved exhaust or bleed type at 14, 41 & 73 scim, & Fail-Safe model |
 | Manual Pneumatic Override/Electric MPOE: Installs between controller and actuator to provide manual override in case of controller malfunction or during system checkout. PRV, terminal strip, switch and pneumatic connections mounted in twenty gauge metal bracket. |
 | 100 psig Pressure to Analog Voltage or Current Output PTP100: Input: 20 - 100 psig air pressure. Output: 1 - 5 VDC, 2 - 10 VDC, 3 - 15 VDC, & 4 - 20mA @ 750 ohm load impedance. Power 24 VAC or 24 VDC @ 50mA max. Size: 3.75" L x 2.25" W x 1.5" H. Brass barbed fittings in anodized aluminum manifold. |
 | Pressure to Analog Voltage or Current Output PTP: Input: 3 - 15, 3 - 30 or 0 - minus 7.5 psig air pressure. Output: 1 - 5 VDC, 2 - 10 VDC, 3 - 15 VDC, & 4 - 20mA @ 750ohm load impedance. Power: 24 VAC or 24 VDC @ 50mA max. Size: 3.75" L x 2.25" W x 1.5" H. Aluminum silver anodized manifold. Gauge available. |
 | Floating Point to Pneumatic Output PTS4.1: Input: Two Digital (relay, triac, or transistor). Output: 0 - 10, 5 - 15, or 0 - 15 psig air pressure (jumper selectable). Rate of Change: 90 seconds. 1% Accuracy at room temperature. Power: 24 VDC or 24 VAC @ 4 VA. Size: 3.25" L x 2.25" W x 1.5" H. Anodized aluminum manifold. Gauge optional. |
 | Analog to 100 psig Output PXP100: Input ranges/impedance: 0 - 5 VDC, 0 - 10 VDC or 0 - 15 VDC/10 Kohm, or 0 - 20mA/250 ohm. Output: 0 - 100 psig. Feedback: 0 - 5 VDC= 0 - 100 psig. Power: 24 VAC or VDC @ 150mA. Size: 3.25" L x 2.25" W x 1.5" H. Valved exhaust, anodized aluminum manifold. |
